71806 bearing: complete specifications & equivalents
The 71806 is a ISO 15 radial bearing sized 30 x 42 x 7 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | Generic ISO interchange (unbranded) |
| Bore diameter d | 30 mm |
| Outer diameter D | 42 mm |
| Width B | 7 mm |
| Seal / shield | open |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | brass |
| Operating temperature | -40 to +150 °C |
| Mass (geometry estimate) | 24 g |
| Standard | ISO 15 |
| Catalog version | iso15-ed4-geometry |
| Last verified | 2026-09-24 |
Source: ISO 15 boundary-dimensions standard · extracted 2026-09-24
Standard-interchange bearing: dimensions per ISO 15; CN clearance, P0 tolerance and a stamped-steel cage are catalogue defaults unless the supplier states otherwise, and mass is a geometry-derived estimate. Brand catalogue load ratings and limiting speeds for 71806 are being backfilled — use the inquiry form for certified values.
Dimensions in inches & 71800-series range
| Bore d | 1.181 in |
|---|---|
| Outer diameter D | 1.654 in |
| Width B | 0.276 in |
| ISO bore code | 06 |
| Radial section height (D−d)/2 | 6 mm |
| Smallest bore in 71800-series | 20 mm |
| Largest outer diameter in 71800-series | 125 mm |
| Width range across 71800-series | 7–13 mm |
| Bore position in 71800-series (smallest first) | 3 of 17 |
| Bore above smallest 71800-series size | 10 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 71806 model number is decoded
In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71806 carries bore code 06 = 30 mm. Outside diameter 42 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61806 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 30 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.
Typical equipment & failure modes
Common applications
- medical and lab spindles
- clutch and idler shafts
- semiconductor handling axes
- packaging machinery
Known failure patterns
- raceway smearing under marginal lubrication at start-up before oil climb reaches the contact
- cage fracture from operation beyond the limiting speed with inadequate lubricant
- fretting corrosion on a loose shaft seat that lets the inner ring creep
- false brinelling from vibration while the shaft is stationary
Selection pitfalls — read before you substitute
- At a 30 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.
- The 718xx thin section at 30 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7206.
- The 42 mm outer ring of 71806 is only 6.0 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 7 mm-wide raceway long before the load rating is reached.
- Angular-contact 71806 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.
- Preload class matters: a 71806 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.
Frequently asked questions
What are the dimensions of a 71806 angular-contact bearing?
A 71806 single-row angular-contact ball bearing has a 30 mm bore, 42 mm outer diameter and 7 mm width (1.181 × 1.654 × 0.276 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 24 g for a brass-cage unit; catalogue masses vary with cage and ball complement.
How does the 71806 bore code work?
The last two digits of 71806 are bore code 06, giving 06 × 5 = 30 mm bore. The 42 mm outside diameter and 7 mm width follow the ISO 15 diameter series, shared with the 61806 deep-groove envelope.
What is the contact angle of 71806?
The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue.
Can a single 71806 take axial load in both directions?
No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load.
Why is the 71806 ring section so thin?
The 718/719 dimension series save radial space: at a 30 mm bore the 71806 envelope is 30×42×7 mm with a 6.0 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore.
Reviewed & verified by the MPN Base engineering desk against source catalog iso15-ed4-geometry on 2026-09-24. Read our editorial & correction policy.