71812 bearing: complete specifications & equivalents
The 71812 is a ISO 15 radial bearing sized 60 x 78 x 10 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | Generic ISO interchange (unbranded) |
| Bore diameter d | 60 mm |
| Outer diameter D | 78 mm |
| Width B | 10 mm |
| Seal / shield | open |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | brass |
| Operating temperature | -40 to +150 °C |
| Mass (geometry estimate) | 100 g |
| Standard | ISO 15 |
| Catalog version | iso15-ed4-geometry |
| Last verified | 2026-09-24 |
Source: ISO 15 boundary-dimensions standard · extracted 2026-09-24
Standard-interchange bearing: dimensions per ISO 15; CN clearance, P0 tolerance and a stamped-steel cage are catalogue defaults unless the supplier states otherwise, and mass is a geometry-derived estimate. Brand catalogue load ratings and limiting speeds for 71812 are being backfilled — use the inquiry form for certified values.
Dimensions in inches & 71800-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 3.071 in |
| Width B | 0.394 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 9 mm |
| Smallest bore in 71800-series | 20 mm |
| Largest outer diameter in 71800-series | 125 mm |
| Width range across 71800-series | 7–13 mm |
| Bore position in 71800-series (smallest first) | 9 of 17 |
| Bore above smallest 71800-series size | 40 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 71812 model number is decoded
In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71812 carries bore code 12 = 60 mm. Outside diameter 78 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61812 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 60 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.
Typical equipment & failure modes
Common applications
- medical and lab spindles
- clutch and idler shafts
- semiconductor handling axes
- packaging machinery
Known failure patterns
- raceway spalling from axial overload exceeding the single-direction thrust rating
- preload loss after a paired set runs loose, letting the balls skid and smear the raceway
- raceway smearing under marginal lubrication at start-up before oil climb reaches the contact
- cage fracture from operation beyond the limiting speed with inadequate lubricant
Selection pitfalls — read before you substitute
- Thermal expansion on this 60 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.
- The 718xx thin section at 60 mm bore has only a 9.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7212.
- With a 9.0 mm radial section on a 60 mm bore, the 71812 ring has little stiffness of its own: it copies the seat geometry, so grind the 60 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 78 mm housing.
- A single 71812 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.
- The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.
Frequently asked questions
What are the dimensions of a 71812 angular-contact bearing?
A 71812 single-row angular-contact ball bearing has a 60 mm bore, 78 mm outer diameter and 10 mm width (2.362 × 3.071 × 0.394 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 100 g for a brass-cage unit; catalogue masses vary with cage and ball complement.
How does the 71812 bore code work?
The last two digits of 71812 are bore code 12, giving 12 × 5 = 60 mm bore. The 78 mm outside diameter and 10 mm width follow the ISO 15 diameter series, shared with the 61812 deep-groove envelope.
What is the contact angle of 71812?
The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue.
Can a single 71812 take axial load in both directions?
No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load.
Why is the 71812 ring section so thin?
The 718/719 dimension series save radial space: at a 60 mm bore the 71812 envelope is 60×78×10 mm with a 9.0 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore.
Reviewed & verified by the MPN Base engineering desk against source catalog iso15-ed4-geometry on 2026-09-24. Read our editorial & correction policy.