6011-RSR bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6011-RSR model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6011 carries bore code 11 = 55 mm. Outside diameter 90 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 55 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NSK's non-contact seal suffix is VV (catalogue number 6011VV), mapped here from the industry-neutral -RSR spelling; speed capability is close to the open bearing but VV is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 55 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6011 with C3 clearance and re-check the residual value after mounting.
• Choosing the 60xx extra-light section saves radial space at 55 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6211 before committing to the smaller envelope.
• RSR low-friction seals on 6011-RSR run faster than contact-seal 6011-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 6011-2RS instead.
• The low-drag lip of 6011-RSR barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• Vibration during standstill brinells the raceways of a 55 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 18 mm-wide ring of 6011-RSR drags the lip and overheats it.
• NSK catalogues this low-friction non-contact seal as 6011VV (suffix VV), mapped here from the industry-neutral -RSR spelling. NSK rates its speed capability close to the open bearing, but VV is not liquid-tight — for wet or fine-dust duty step up to the DDU contact seal (industry-neutral -2RS).
• At 55 mm bore 6011 is in NSK's upper general-purpose range; the pressed-steel cage is standard, but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• At 31 kN dynamic load rating (C) and 21.2 kN static (C0), 6011 is a medium-load NSK bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NSK catalogue.
• At 381 g, 6011 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 55×90×18 mm envelope of 6011 gives a D/d ratio of 1.64 and 17.5 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 31/21.2 kN load ratings, mass 381 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6011VV on the 55×90×18 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6011 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 6011; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.