6012-2RS-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6012-2RS-NSK model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6012 carries bore code 12 = 60 mm. Outside diameter 95 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 60 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NSK's contact-seal catalogue number is 6012DDU (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 60 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6012 with C3 clearance and re-check the residual value after mounting.
• The 60xx extra-light section at 60 mm bore uses a smaller 95 mm OD than a 6212; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
• Contact seals add drag and heat: 6012-2RS-NSK runs slower and cooler-limited than the open 6012; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Heat is the enemy of the sealed 6012-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 95 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6012-2RS-NSK.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• NSK catalogues the contact-sealed version as 6012DDU (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. NSK's DDU lip design is single-lip contact, so grease life is longer than VV but drag torque is higher.
• At 60 mm bore 6012 is in NSK's upper general-purpose range; the pressed-steel cage is standard, but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• At 32.5 kN dynamic load rating (C) and 23.2 kN static (C0), 6012 is a medium-load NSK bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NSK catalogue.
• At 412 g, 6012 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 60×95×18 mm envelope of 6012 gives a D/d ratio of 1.58 and 17.5 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 32.5/23.2 kN load ratings, mass 412 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6012DDU on the 60×95×18 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6012 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.
• Keep NSK bearings in the original packaging until fitting: the wrapper carries the production lot, and the unopened shelf life of greased sealed units is typically quoted at three to five years in dry, vibration-free storage.