6044-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6044-NSK model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6044 carries bore code 44 = 220 mm. Outside diameter 340 mm and width 56 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 220 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 220 mm of 6044-NSK demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• Choosing the 60xx extra-light section saves radial space at 220 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6244 before committing to the smaller envelope.
• The open 6044-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 220×340×56 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Storage matters for open bearings: 6044-NSK leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 6000-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Shaft and housing fillets must clear the bearing chamfer so the 56 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• The open 6044 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 220 mm bore places 6044 at the upper end of NSK's single-row deep-groove catalogue for the E1103 Part C extract; this is a heavy-engineering bearing where centrifugal force and cage inertia dominate the design envelope. NSK supplies a machined brass cage (suffix M) and expects oil lubrication with a defined relubrication interval — do not use catalogue grease speed figures for this size without an NSK engineering review.
• NSK rates 6044 at 259 kN dynamic (C) and 271 kN static (C0); this is an extreme-load bearing at the top of the E1103 Part C single-row deep-groove range, where mounting, shaft stiffness and housing alignment dominate the achievable life. Consult NSK engineering for a full application review rather than relying on catalogue L10 alone.
• At 18600 g (18.6 kg), 6044 is a heavy NSK bearing that requires a crane or hoist for handling; induction-heat the inner ring (max 120 °C) and use a mechanical puller for removal — never apply heat directly to the balls or cage.
• The 220×340×56 mm envelope of 6044 gives a D/d ratio of 1.55 and 60.0 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 259/271 kN load ratings, mass 18600 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6044 on the 220×340×56 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6044 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.