61801-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61801-NSK model number is decoded

61801 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 12 by five gives the 12 mm bore; the 21 mm outside diameter and 5 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 12 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 12 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61801 with C3 for those conditions.
• Only 4.5 mm of radial section separates bore and OD on the 618xx series at 12 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6212.
• Storage matters for open bearings: 61801-NSK leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61801 units.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 21 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 61801-NSK.
• A 12 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• The open 61801 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• At 12 mm bore the 61801 sits in NSK's small-bore range; NSK ships these sizes with a pressed-steel cage and P0 tolerance as standard, and NSK's EA (extra-precision) or P5 class is a special-order upgrade for spindle duty — do not assume catalogue P0 figures hold for instrument use without an NSK engineering check.
• At 2.11 kN dynamic load rating (C) and 1.04 kN static (C0), 61801 is a light-load NSK bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 6 g, 61801 is a lightweight NSK bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 12×21×5 mm envelope of 61801 gives a D/d ratio of 1.75 and 4.5 mm radial section height — a standard NSK medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to NSK's listed speed ratings, and C3 clearance is the common choice for hot shafts.
• The 2.11/1.04 kN load ratings, mass 6 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6801 on the 12×21×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61801 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 61801 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.
• Keep NSK bearings in the original packaging until fitting: the wrapper carries the production lot, and the unopened shelf life of greased sealed units is typically quoted at three to five years in dry, vibration-free storage.