61801-ZZ-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61801-ZZ-NSK model number is decoded

In the 61800-series (diameter series 8 of ISO 15) the last two digits encode the bore: 61801 carries bore code 12 = 12 mm. Outside diameter 21 mm and width 5 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 12 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NSK catalogue order number: 6801ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 12 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61801 with C3 for those conditions.
• Only 4.5 mm of radial section separates bore and OD on the 618xx series at 12 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6212.
• Do not wash 61801-ZZ-NSK in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Shielded 61801-ZZ-NSK units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• A 12 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 61801-ZZ-NSK-C3. No clearance suffix means normal CN clearance.
• NSK catalogues the shielded version as 6801ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NSK order number when buying through an NSK channel.
• At 12 mm bore the 61801 sits in NSK's small-bore range; NSK ships these sizes with a pressed-steel cage and P0 tolerance as standard, and NSK's EA (extra-precision) or P5 class is a special-order upgrade for spindle duty — do not assume catalogue P0 figures hold for instrument use without an NSK engineering check.
• At 2.11 kN dynamic load rating (C) and 1.04 kN static (C0), 61801 is a light-load NSK bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 6 g, 61801 is a lightweight NSK bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 12×21×5 mm envelope of 61801 gives a D/d ratio of 1.75 and 4.5 mm radial section height — a standard NSK medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to NSK's listed speed ratings, and C3 clearance is the common choice for hot shafts.
• The 2.11/1.04 kN load ratings, mass 6 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6801ZZ on the 12×21×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61801 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 61801; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.