61812-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61812-NSK model number is decoded

61812 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 12 by five gives the 60 mm bore; the 78 mm outside diameter and 10 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 60 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61812 with C3 for those conditions.
• The 618xx thin section at 60 mm bore has only a 9.0 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6212.
• The open 61812-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 60×78×10 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61812 units.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61800-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Do not quieten a noisy bearing by preloading it: the 61800-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• The open 61812 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• At 60 mm bore 61812 is in NSK's upper general-purpose range; the pressed-steel cage is standard, but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• NSK rates 61812 at 12.6 kN dynamic (C) and 10.9 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 103 g, 61812 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 60×78×10 mm envelope of 61812 gives a D/d ratio of 1.30 and only 9.0 mm radial section height — this is an ultra-thin section in NSK's E1103 catalogue where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 12.6/10.9 kN load ratings, mass 103 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6812 on the 60×78×10 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61812 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.
• NSK's VV non-contact seal keeps frictional torque close to the open 61812; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.