61836-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61836-NSK model number is decoded

In the 61800-series (diameter series 8 of ISO 15) the last two digits encode the bore: 61836 carries bore code 36 = 180 mm. Outside diameter 225 mm and width 22 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 180 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 180 mm bore the ring mass is significant: heat 61836 on an induction heater (max 120 °C), never over an open flame, and plan puller access or a withdrawal sleeve now for the day it has to come off again.
• The 618xx thin section at 180 mm bore has only a 22.5 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6236.
• The open 61836-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 180×225×22 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61836 units.
• Vibration during standstill brinells the raceways of a 180 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Do not quieten a noisy bearing by preloading it: the 61800-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• The open 61836 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 180 mm bore places 61836 in NSK's large-size range; at these diameters the pressed-steel cage is speed-limited and NSK commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NSK distributor, and do not extrapolate small-bore speed ratings to this size.
• NSK rates 61836 at 66.5 kN dynamic (C) and 78.5 kN static (C0); this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 1980 g (2.0 kg), 61836 needs mechanical handling for mounting; NSK recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 180×225×22 mm envelope of 61836 gives a D/d ratio of 1.25 and only 22.5 mm radial section height — this is an ultra-thin section in NSK's E1103 catalogue where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 66.5/78.5 kN load ratings, mass 1980 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6836 on the 180×225×22 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61836 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 61836; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.