61917-RSR bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61917-RSR model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61917 carries bore code 17 = 85 mm. Outside diameter 120 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 85 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NSK's non-contact seal suffix is VV (catalogue number 6917VV), mapped here from the industry-neutral -RSR spelling; speed capability is close to the open bearing but VV is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 619xx thin section at 85 mm bore (17.5 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
• RSR low-friction seals on 61917-RSR run faster than contact-seal 61917-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61917-2RS instead.
• The non-contact lip of 61917-RSR does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 85 mm bore position before relying on it as sealed-for-life.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• A 85 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• NSK catalogues this low-friction non-contact seal as 6917VV (suffix VV), mapped here from the industry-neutral -RSR spelling. NSK rates its speed capability close to the open bearing, but VV is not liquid-tight — for wet or fine-dust duty step up to the DDU contact seal (industry-neutral -2RS).
• At 85 mm bore 61917 is in NSK's medium industrial range; the pressed-steel cage is standard, but large-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• NSK rates 61917 at 35 kN dynamic (C) and 29.6 kN static (C0); this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 550 g, 61917 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 85×120×18 mm envelope of 61917 gives a D/d ratio of 1.41 and 17.5 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 35/29.6 kN load ratings, mass 550 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6917VV on the 85×120×18 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61917 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 61917; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.