61938-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61938-NSK model number is decoded

61938 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 38 by five gives the 190 mm bore; the 260 mm outside diameter and 33 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 190 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 190 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 619xx thin section (35.0 mm section height at 190 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• The open 61938-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 190×260×33 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61900-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61938 units.
• A 190 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• Do not quieten a noisy bearing by preloading it: the 61900-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• The open 61938 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 190 mm bore places 61938 in NSK's large-size range; at these diameters the pressed-steel cage is speed-limited and NSK commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NSK distributor, and do not extrapolate small-bore speed ratings to this size.
• At 124 kN dynamic load rating (C) and 127 kN static (C0), 61938 is a heavy-load NSK bearing for industrial gearboxes and large conveyors; NSK expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 5180 g (5.2 kg), 61938 is a heavy NSK bearing that requires a crane or hoist for handling; induction-heat the inner ring (max 120 °C) and use a mechanical puller for removal — never apply heat directly to the balls or cage.
• The 190×260×33 mm envelope of 61938 gives a D/d ratio of 1.37 and only 35.0 mm radial section height — this is an ultra-thin section in NSK's E1103 catalogue where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 124/127 kN load ratings, mass 5180 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6938 on the 190×260×33 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61938 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 61938; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.