6220-RSR bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6220-RSR model number is decoded

6220-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 20 by five gives the 100 mm bore; the 180 mm outside diameter and 34 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 100 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK's non-contact seal suffix is VV (catalogue number 6220VV), mapped here from the industry-neutral -RSR spelling; speed capability is close to the open bearing but VV is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 62xx light series is the default general-purpose section at 100 mm bore; before upgrading to a 6320 for extra capacity, confirm the housing accepts a 180 mm OD and 34 mm width — it is not a drop-in swap.
• The low-drag lip of 6220-RSR barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• The non-contact lip of 6220-RSR does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 100 mm bore position before relying on it as sealed-for-life.
• Never mix components between two 6220-RSR units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• Measure the shaft, do not trust the drawing: a 100 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6220-RSR.
• NSK catalogues this low-friction non-contact seal as 6220VV (suffix VV), mapped here from the industry-neutral -RSR spelling. NSK rates its speed capability close to the open bearing, but VV is not liquid-tight — for wet or fine-dust duty step up to the DDU contact seal (industry-neutral -2RS).
• At 100 mm bore 6220 is in NSK's medium industrial range; the pressed-steel cage is standard, but large-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• At 134 kN dynamic load rating (C) and 93 kN static (C0), 6220 is a heavy-load NSK bearing for industrial gearboxes and large conveyors; NSK expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 3170 g (3.2 kg), 6220 needs mechanical handling for mounting; NSK recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 100×180×34 mm envelope of 6220 gives a D/d ratio of 1.80 and 40.0 mm radial section height — a standard NSK medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to NSK's listed speed ratings, and C3 clearance is the common choice for hot shafts.
• The 134/93 kN load ratings, mass 3170 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6220VV on the 100×180×34 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6220 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.