6411-2RS bearing: complete specifications & equivalents
The 6411-2RS is a ISO 15 radial bearing sized 55 x 140 x 33 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 55 mm |
| Outer diameter D | 140 mm |
| Width B | 33 mm |
| Seal / shield | 2RS |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Operating temperature | -30 to +110 °C |
| Mass (geometry estimate) | 2192 g |
| Standard | ISO 15 |
| Catalog version | iso15-ed4-geometry |
| Last verified | 2026-09-23 |
Source: ISO 15 boundary-dimensions standard · extracted 2026-09-23
Standard-interchange bearing: dimensions per ISO 15; CN clearance, P0 tolerance and a stamped-steel cage are catalogue defaults unless the supplier states otherwise, and mass is a geometry-derived estimate. Brand catalogue load ratings and limiting speeds for 6411 are being backfilled — use the inquiry form for certified values.
Dimensions in inches & 6400-series range
| Bore d | 2.165 in |
|---|---|
| Outer diameter D | 5.512 in |
| Width B | 1.299 in |
| ISO bore code | 11 |
| Radial section height (D−d)/2 | 42.5 mm |
| Smallest bore in 6400-series | 10 mm |
| Largest outer diameter in 6400-series | 250 mm |
| Width range across 6400-series | 12–58 mm |
| Bore position in 6400-series (smallest first) | 12 of 21 |
| Bore above smallest 6400-series size | 45 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6411 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 55×140×33 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6411-2RS model number is decoded
In the 6400-series (ISO 15 diameter series 4) the last two digits encode the bore: 6411 carries bore code 11 = 55 mm. Outside diameter 140 mm and width 33 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 55 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude.
Typical equipment & failure modes
Common applications
- industrial fans
- industrial electric motors
- centrifugal and positive-displacement pumps
- gearboxes and speed reducers
Known failure patterns
- seal-lip hardening and loss of pre-grease in sustained high-temperature service
- grease-life expiry in the sealed-for-life cavity (no relubrication path)
- cage damage from operation beyond the limiting speed
- electrical pitting in VFD-driven motors without grounding protection
Selection pitfalls — read before you substitute
- Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 6411 with C3 for those conditions.
- The 64xx heavy section at 55 mm bore (140 mm OD) is built for high-load, lower-speed duty; specifying it in a high-rpm motor gives excess heat and short grease life — use 62/63 there.
- Contact seals add drag and heat: 6411-2RS runs slower and cooler-limited than the open 6411; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
- Never wash a sealed 6411-2RS in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
- Shaft and housing fillets must clear the bearing chamfer so the 33 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
Frequently asked questions
What are the dimensions of a 6411-2RS bearing?
A 6411-2RS deep-groove ball bearing has a 55 mm bore, 140 mm outer diameter and 33 mm width (2.165 × 5.512 × 1.299 in), per ISO 15 boundary dimensions. It is fitted with two contact rubber seals and is normally pre-greased. Geometry-based estimated mass is about 2192 g for a steel-cage unit; catalogue masses vary slightly with seal and cage design.
How does the 6411 bore code work?
The last two digits of 6411 are bore code 11, giving 11 × 5 = 55 mm bore. The 140 mm outside diameter and 33 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the 2RS suffix on 6411-2RS mean?
2RS means two contact elastomer seals, one each side, usually over a lifetime grease fill. Sealing against dust and moisture is better than ZZ shields, but the lip drag lowers the speed and temperature ceiling.
How does the 6400 compare with other series at the same 55 mm bore?
The '4' is the heavy diameter series: 140×33 mm, 42.5 mm radial section at 55 mm bore — the highest-capacity single-row 6xx option here, aimed at lower-speed, high-load shafts.
Are 6411 bearings from different brands interchangeable?
For boundary dimensions, yes: every brand's 6411 uses the same ISO 15 envelope (55×140×33 mm). Load ratings, limiting speeds, clearance, precision class and sealing design can differ, so verify those in the supplier catalogue when substituting. Seal suffixes also differ by brand (2RS, DDU, LLU and similar).
Reviewed & verified by the MPN Base engineering desk against source catalog iso15-ed4-geometry on 2026-09-23. Read our editorial & correction policy.