6419-2RS bearing: complete specifications & equivalents
The 6419-2RS is a ISO 15 radial bearing sized 95 x 240 x 55 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 95 mm |
| Outer diameter D | 240 mm |
| Width B | 55 mm |
| Seal / shield | 2RS |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Mass (geometry estimate) | 10707 g |
| Standard | ISO 15 |
| Catalog version | iso15-ed4-geometry |
| Last verified | 2026-09-24 |
Source: ISO 15 boundary-dimensions standard · extracted 2026-09-24
Standard-interchange bearing: dimensions per ISO 15; CN clearance, P0 tolerance and a stamped-steel cage are catalogue defaults unless the supplier states otherwise, and mass is a geometry-derived estimate. Brand catalogue load ratings and limiting speeds for 6419 are being backfilled — use the inquiry form for certified values.
Dimensions in inches & 6400-series range
| Bore d | 3.74 in |
|---|---|
| Outer diameter D | 9.449 in |
| Width B | 2.165 in |
| ISO bore code | 19 |
| Radial section height (D−d)/2 | 72.5 mm |
| Smallest bore in 6400-series | 10 mm |
| Largest outer diameter in 6400-series | 250 mm |
| Width range across 6400-series | 12–58 mm |
| Bore position in 6400-series (smallest first) | 20 of 21 |
| Bore above smallest 6400-series size | 85 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6419 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range. Brand-specific OEM equivalents pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6419-2RS model number is decoded
In the 6400-series (ISO 15 diameter series 4) the last two digits encode the bore: 6419 carries bore code 19 = 95 mm. Outside diameter 240 mm and width 55 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 95 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude.
Typical equipment & failure modes
Common applications
- large gearboxes
- industrial fans and blowers
- hoists and winches
- heavy conveyors
Known failure patterns
- seal-lip hardening and loss of pre-grease in sustained high-temperature service
- grease-life expiry in the sealed-for-life cavity (no relubrication path)
- cage damage from operation beyond the limiting speed
- electrical pitting in VFD-driven motors without grounding protection
Selection pitfalls — read before you substitute
- Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 64xx heavy section at 95 mm bore (240 mm OD) is built for high-load, lower-speed duty; specifying it in a high-rpm motor gives excess heat and short grease life — use 62/63 there.
- Contact seals add drag and heat: 6419-2RS runs slower and cooler-limited than the open 6419; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
- Never wash a sealed 6419-2RS in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
- Deep-groove ball bearings tolerate only minutes of misalignment; if the 240 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6419-2RS.
Frequently asked questions
What are the dimensions of a 6419-2RS bearing?
A 6419-2RS deep-groove ball bearing has a 95 mm bore, 240 mm outer diameter and 55 mm width (3.74 × 9.449 × 2.165 in), per ISO 15 boundary dimensions. It is fitted with two contact rubber seals and is normally pre-greased. Geometry-based estimated mass is about 10707 g for a steel-cage unit; catalogue masses vary slightly with seal and cage design.
How does the 6419 bore code work?
The last two digits of 6419 are bore code 19, giving 19 × 5 = 95 mm bore. The 240 mm outside diameter and 55 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the 2RS suffix on 6419-2RS mean?
2RS means two contact elastomer seals, one each side, usually over a lifetime grease fill. Sealing against dust and moisture is better than ZZ shields, but the lip drag lowers the speed and temperature ceiling.
How does the 6400 compare with other series at the same 95 mm bore?
The '4' is the heavy diameter series: 240×55 mm, 72.5 mm radial section at 95 mm bore — the highest-capacity single-row 6xx option here, aimed at lower-speed, high-load shafts.
Are 6419 bearings from different brands interchangeable?
For boundary dimensions, yes: every brand's 6419 uses the same ISO 15 envelope (95×240×55 mm). Load ratings, limiting speeds, clearance, precision class and sealing design can differ, so verify those in the supplier catalogue when substituting. Seal suffixes also differ by brand (2RS, DDU, LLU and similar).
Reviewed & verified by the MPN Base engineering desk against source catalog iso15-ed4-geometry on 2026-09-24. Read our editorial & correction policy.