MPNbase

105×160×26 mm bearings

15 models from 4 brands across 3 types share this ISO 15 envelope: 105 mm bore, 160 mm outside diameter, 26 mm width (4.134×6.299×1.024 in), 27.5 mm radial section.

15 models fit this space 4 brands 14 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6021 Deep Groove Ball SKF open CN 76.1 65.5 1600
6021-2RS Deep Groove Ball SKF 2RS CN 76.1 65.5 1650
6021-2RS-NSK Deep Groove Ball NSK 2RS CN 79.5 66 1580
6021-M Deep Groove Ball SKF open CN 76.1 65.5 1850
6021-NSK Deep Groove Ball NSK open CN 79.5 66 1580
6021-RSR Deep Groove Ball NSK RSR CN 79.5 66 1580
6021-ZZ Deep Groove Ball SKF ZZ CN 76.1 65.5 1650
6021-ZZ-NSK Deep Groove Ball NSK ZZ CN 79.5 66 1580
7021 Angular Contact Ball GENERIC-ISO open CN — — 1519
7021-NTN Angular Contact Ball NTN open CN 88.5 81.5 1860
N1021 Cylindrical Roller NTN open CN 117 142 1810
NJ1021 Cylindrical Roller NTN open CN 117 142 1810
NU1021 Cylindrical Roller NTN open CN 117 142 1810
NU1021-ML Cylindrical Roller SKF open CN 101 137 1900
NUP1021 Cylindrical Roller NTN open CN 117 142 1810

Note: catalogue dynamic load ratings for this envelope span 76.1– 117.0 kN — a 54% spread between designs in the very same 105×160×26 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 105 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6021, 6021-2RS, 6021-2RS-NSK, 6021-M, 6021-NSK, 6021-RSR, 6021-ZZ, 6021-ZZ-NSK, 7021, 7021-NTN, N1021, NJ1021, NU1021, NU1021-ML, NUP1021.

Frequently asked questions

Are all 105×160×26 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 105 mm bore, 160 mm OD, 26 mm width (4.134×6.299×1.024 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 15 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 105×160×26?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 105×160×26 mm in inches?

105×160×26 mm converts to 4.134×6.299×1.024 in, with a 27.5 mm (1.083 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6021, 6021-2RS, 6021-2RS-NSK mount in the same space despite different internal designs.