150×210×28 mm bearings
3 models from 1 brand across 1 type share this ISO 15 envelope: 150 mm bore, 210 mm outside diameter, 28 mm width (5.906×8.268×1.102 in), 30 mm radial section.
3 models fit this space 1 brand 3 with catalogue C rating
Dimensional interchange — verify before substituting
These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.
| Model | Type | Brand | Seal | Clearance | C (kN) | C0 (kN) | Mass (g) |
|---|---|---|---|---|---|---|---|
| 61930 | Deep Groove Ball | NSK | open | CN | 93.5 | 90.5 | 3010 |
| 61930-2RS | Deep Groove Ball | NSK | 2RS | CN | 93.5 | 90.5 | 3010 |
| 61930-ZZ | Deep Groove Ball | NSK | ZZ | CN | 93.5 | 90.5 | 3010 |
Substitution verification checklist
- Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
- Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
- Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
- Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
- Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.
Browse all 150 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 61930, 61930-2RS, 61930-ZZ.
Frequently asked questions
Are all 150×210×28 mm bearings interchangeable?
They share the same ISO 15 boundary dimensions — 150 mm bore, 210 mm OD, 28 mm width (5.906×8.268×1.102 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 3 models listed here and must be checked against the duty before substitution.
Is it a drop-in replacement if two bearings both measure 150×210×28?
Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.
What is 150×210×28 mm in inches?
150×210×28 mm converts to 5.906×8.268×1.102 in, with a 30 mm (1.181 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 61930, 61930-2RS, 61930-ZZ mount in the same space despite different internal designs.