MPNbase

220×400×108 mm bearings

9 models from 1 brand across 2 types share this ISO 15 envelope: 220 mm bore, 400 mm outside diameter, 108 mm width (8.661×15.748×4.252 in), 90 mm radial section.

9 models fit this space 1 brand 9 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
C2244 CARB Toroidal Roller SKF open CN 2000 2500 57500
C2244-K CARB Toroidal Roller SKF open CN 2000 2500 57500
NCF2244-ECJB Cylindrical Roller SKF open CN 1760 2600 58500
NCF2244-ECJB-PEX Cylindrical Roller SKF open CN 2000 2600 58500
NCF2244-V Cylindrical Roller SKF open CN 1830 2750 58000
NJ2244-ECML Cylindrical Roller SKF open CN 1570 2280 60000
NU2244-ECML Cylindrical Roller SKF open CN 1570 2280 58000
NUH2244-ECMH Cylindrical Roller SKF open CN 1760 2600 59000
NUH2244-ECMH-PEX Cylindrical Roller SKF open CN 2000 2600 59000

Note: catalogue dynamic load ratings for this envelope span 1570.0– 2000.0 kN — a 27% spread between designs in the very same 220×400×108 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 220 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: C2244, C2244-K, NCF2244-ECJB, NCF2244-ECJB-PEX, NCF2244-V, NJ2244-ECML, NU2244-ECML, NUH2244-ECMH, NUH2244-ECMH-PEX.

Frequently asked questions

Are all 220×400×108 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 220 mm bore, 400 mm OD, 108 mm width (8.661×15.748×4.252 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 9 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 220×400×108?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 220×400×108 mm in inches?

220×400×108 mm converts to 8.661×15.748×4.252 in, with a 90 mm (3.543 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as C2244, C2244-K, NCF2244-ECJB mount in the same space despite different internal designs.