260×400×104 mm bearings

12 models from 3 brands across 4 types share this ISO 15 envelope: 260 mm bore, 400 mm outside diameter, 104 mm width (10.236×15.748×4.094 in), 70 mm radial section.

12 models fit this space 3 brands 12 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23052 Spherical Roller SKF open CN 1675 2550 48500
23052-CCK-W33 Spherical Roller SKF open CN 1675 2550 60500
23052EMD1 Spherical Roller NTN open CN 2060 2910 47800
23052EMKD1 Spherical Roller NTN open CN 2060 2910 46300
323052UTG Tapered Roller NTN open CN 1470 2190 47700
413052UTG Tapered Roller NTN open CN 1070 1540 43400
C3052 CARB Toroidal Roller SKF open CN 1760 2850 47000
C3052-K CARB Toroidal Roller SKF open CN 1760 2850 47000
NCF3052-CV Cylindrical Roller SKF open CN 1540 2550 46500
NN3052 Cylindrical Roller NTN open CN 1180 1990 47400
NN3052K Cylindrical Roller NTN open CN 1180 1990 45800
SL183052-TB Cylindrical Roller FAG open CN 1600 2500 44500

Note: catalogue dynamic load ratings for this envelope span 1070.0– 2060.0 kN — a 93% spread between designs in the very same 260×400×104 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 260 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23052, 23052-CCK-W33, 23052EMD1, 23052EMKD1, 323052UTG, 413052UTG, C3052, C3052-K, NCF3052-CV, NN3052, NN3052K, SL183052-TB.

Frequently asked questions

Are all 260×400×104 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 260 mm bore, 400 mm OD, 104 mm width (10.236×15.748×4.094 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 12 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 260×400×104?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 260×400×104 mm in inches?

260×400×104 mm converts to 10.236×15.748×4.094 in, with a 70 mm (2.756 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23052, 23052-CCK-W33, 23052EMD1 mount in the same space despite different internal designs.