340×520×133 mm bearings

11 models from 3 brands across 4 types share this ISO 15 envelope: 340 mm bore, 520 mm outside diameter, 133 mm width (13.386×20.472×5.236 in), 90 mm radial section.

11 models fit this space 3 brands 11 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23068EMD1 Spherical Roller NTN open CN 2990 4690 98500
23068EMKD1 Spherical Roller NTN open CN 2990 4690 95500
323068UTG Tapered Roller NTN open CN 2420 3750 100000
413068UTG Tapered Roller NTN open CN 1890 2870 93100
C3068-KM CARB Toroidal Roller SKF open CN 2900 5000 100000
C3068-M CARB Toroidal Roller SKF open CN 2900 5000 100000
NCF3068-CV Cylindrical Roller SKF open CN 2380 4150 95000
NN3068 Cylindrical Roller NTN open CN 1800 3200 102000
NN3068K Cylindrical Roller NTN open CN 1800 3200 98500
NU3068-MA Cylindrical Roller SKF open CN 2200 4150 109000
SL183068-TB Cylindrical Roller FAG open CN 2490 4150 95800

Note: catalogue dynamic load ratings for this envelope span 1800.0– 2990.0 kN — a 66% spread between designs in the very same 340×520×133 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 340 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23068EMD1, 23068EMKD1, 323068UTG, 413068UTG, C3068-KM, C3068-M, NCF3068-CV, NN3068, NN3068K, NU3068-MA, SL183068-TB.

Frequently asked questions

Are all 340×520×133 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 340 mm bore, 520 mm OD, 133 mm width (13.386×20.472×5.236 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 11 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 340×520×133?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 340×520×133 mm in inches?

340×520×133 mm converts to 13.386×20.472×5.236 in, with a 90 mm (3.543 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23068EMD1, 23068EMKD1, 323068UTG mount in the same space despite different internal designs.