360×540×134 mm bearings

10 models from 3 brands across 4 types share this ISO 15 envelope: 360 mm bore, 540 mm outside diameter, 134 mm width (14.173×21.260×5.276 in), 90 mm radial section.

10 models fit this space 3 brands 10 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23072EMD1 Spherical Roller NTN open CN 3070 4910 111000
23072EMKD1 Spherical Roller NTN open CN 3070 4910 108000
323072UTG Tapered Roller NTN open CN 2630 4200 110000
413072UTG Tapered Roller NTN open CN 1880 2810 98200
C3072-KM CARB Toroidal Roller SKF open CN 2900 5000 106000
C3072-M CARB Toroidal Roller SKF open CN 2900 5000 106000
NCF3072-CV Cylindrical Roller SKF open CN 2420 4300 105000
NN3072 Cylindrical Roller NTN open CN 1830 3300 107000
NN3072K Cylindrical Roller NTN open CN 1830 3300 103000
SL183072-TB Cylindrical Roller FAG open CN 2550 4350 101000

Note: catalogue dynamic load ratings for this envelope span 1830.0– 3070.0 kN — a 68% spread between designs in the very same 360×540×134 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 360 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23072EMD1, 23072EMKD1, 323072UTG, 413072UTG, C3072-KM, C3072-M, NCF3072-CV, NN3072, NN3072K, SL183072-TB.

Frequently asked questions

Are all 360×540×134 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 360 mm bore, 540 mm OD, 134 mm width (14.173×21.260×5.276 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 10 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 360×540×134?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 360×540×134 mm in inches?

360×540×134 mm converts to 14.173×21.260×5.276 in, with a 90 mm (3.543 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23072EMD1, 23072EMKD1, 323072UTG mount in the same space despite different internal designs.