380×520×140 mm bearings

6 models from 3 brands across 1 type share this ISO 15 envelope: 380 mm bore, 520 mm outside diameter, 140 mm width (14.961×20.472×5.512 in), 70 mm radial section.

6 models fit this space 3 brands 6 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
NNC4976-CV Cylindrical Roller SKF open CN 2380 5700 92500
NNCF4976-CV Cylindrical Roller SKF open CN 2380 5700 91500
NNCL4976-CV Cylindrical Roller SKF open CN 2380 5700 90500
NNU4976K Cylindrical Roller NTN open CN 1810 4050 80600
SL014976 Cylindrical Roller FAG open CN 2250 5500 92400
SL024976 Cylindrical Roller FAG open CN 2250 5500 90500

Note: catalogue dynamic load ratings for this envelope span 1810.0– 2380.0 kN — a 31% spread between designs in the very same 380×520×140 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 380 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: NNC4976-CV, NNCF4976-CV, NNCL4976-CV, NNU4976K, SL014976, SL024976.

Frequently asked questions

Are all 380×520×140 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 380 mm bore, 520 mm OD, 140 mm width (14.961×20.472×5.512 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 6 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 380×520×140?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 380×520×140 mm in inches?

380×520×140 mm converts to 14.961×20.472×5.512 in, with a 70 mm (2.756 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as NNC4976-CV, NNCF4976-CV, NNCL4976-CV mount in the same space despite different internal designs.