480×700×165 mm bearings

7 models from 2 brands across 4 types share this ISO 15 envelope: 480 mm bore, 700 mm outside diameter, 165 mm width (18.898×27.559×6.496 in), 110 mm radial section.

7 models fit this space 2 brands 7 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23096B Spherical Roller NTN open CN 4050 7700 217000
23096BK Spherical Roller NTN open CN 4050 7700 209000
323096UTG Tapered Roller NTN open CN 3900 6700 210000
413096UTG Tapered Roller NTN open CN 3200 5000 190000
C3096-KM CARB Toroidal Roller SKF open CN 4050 7800 215000
C3096-M CARB Toroidal Roller SKF open CN 4050 7800 215000
NCF3096-CV Cylindrical Roller SKF open CN 3740 7200 205000

Note: catalogue dynamic load ratings for this envelope span 3200.0– 4050.0 kN — a 27% spread between designs in the very same 480×700×165 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 480 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23096B, 23096BK, 323096UTG, 413096UTG, C3096-KM, C3096-M, NCF3096-CV.

Frequently asked questions

Are all 480×700×165 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 480 mm bore, 700 mm OD, 165 mm width (18.898×27.559×6.496 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 7 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 480×700×165?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 480×700×165 mm in inches?

480×700×165 mm converts to 18.898×27.559×6.496 in, with a 110 mm (4.331 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23096B, 23096BK, 323096UTG mount in the same space despite different internal designs.