MPNbase

5×16×12 mm bearings

8 models from 2 brands across 1 type share this ISO 15 envelope: 5 mm bore, 16 mm outside diameter, 12 mm width (0.197×0.630×0.472 in), 5.5 mm radial section.

8 models fit this space 2 brands 8 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
NATR-5 Support Rollers SKF open CN 3.14 3.2 14
NATR-5-PPA Support Rollers SKF open CN 3.14 3.2 14
NATR5 Support Rollers FAG open CN 3.15 3.4 14
NATR5-PP Support Rollers FAG 2RS CN 3.15 3.4 14
NATV-5 Support Rollers SKF open CN 4.73 6.55 15
NATV-5-PPA Support Rollers SKF open CN 4.73 6.55 15
NATV5 Support Rollers FAG open CN 4.9 6.7 15
NATV5-PP Support Rollers FAG 2RS CN 4.9 6.7 15

Note: catalogue dynamic load ratings for this envelope span 3.1– 4.9 kN — a 56% spread between designs in the very same 5×16×12 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 5 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: NATR-5, NATR-5-PPA, NATR5, NATR5-PP, NATV-5, NATV-5-PPA, NATV5, NATV5-PP.

Frequently asked questions

Are all 5×16×12 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 5 mm bore, 16 mm OD, 12 mm width (0.197×0.630×0.472 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 8 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 5×16×12?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 5×16×12 mm in inches?

5×16×12 mm converts to 0.197×0.630×0.472 in, with a 5.5 mm (0.217 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as NATR-5, NATR-5-PPA, NATR5 mount in the same space despite different internal designs.