MPNbase

65×160×37 mm bearings

12 models from 3 brands across 3 types share this ISO 15 envelope: 65 mm bore, 160 mm outside diameter, 37 mm width (2.559×6.299×1.457 in), 47.5 mm radial section.

12 models fit this space 3 brands 11 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6413 Deep Groove Ball SKF open CN 119 78 3350
6413-2RS Deep Groove Ball GENERIC-ISO 2RS CN 119 78 3169
6413-NTN Deep Groove Ball NTN open CN 123 72.5 3300
6413-ZZ Deep Groove Ball GENERIC-ISO ZZ CN 119 78 3169
7413 Angular Contact Ball GENERIC-ISO open CN — — 3169
N413 Cylindrical Roller NTN open CN 202 186 3500
NF413 Cylindrical Roller NTN open CN 202 186 3500
NJ413 Cylindrical Roller SKF open CN 183 190 3650
NJ413-NTN Cylindrical Roller NTN open CN 202 186 3500
NU413 Cylindrical Roller SKF open CN 183 190 3550
NU413-NTN Cylindrical Roller NTN open CN 202 186 3500
NUP413 Cylindrical Roller NTN open CN 202 186 3500

Note: catalogue dynamic load ratings for this envelope span 119.0– 202.0 kN — a 70% spread between designs in the very same 65×160×37 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 65 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6413, 6413-2RS, 6413-NTN, 6413-ZZ, 7413, N413, NF413, NJ413, NJ413-NTN, NU413, NU413-NTN, NUP413.

Frequently asked questions

Are all 65×160×37 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 65 mm bore, 160 mm OD, 37 mm width (2.559×6.299×1.457 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 12 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 65×160×37?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 65×160×37 mm in inches?

65×160×37 mm converts to 2.559×6.299×1.457 in, with a 47.5 mm (1.870 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6413, 6413-2RS, 6413-NTN mount in the same space despite different internal designs.