MPNbase

80×200×48 mm bearings

11 models from 3 brands across 2 types share this ISO 15 envelope: 80 mm bore, 200 mm outside diameter, 48 mm width (3.150×7.874×1.890 in), 60 mm radial section.

11 models fit this space 3 brands 11 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6416 Deep Groove Ball SKF open CN 163 125 6850
6416-2RS Deep Groove Ball GENERIC-ISO 2RS CN 163 125 6463
6416-NTN Deep Groove Ball NTN open CN 181 125 6760
6416-ZZ Deep Groove Ball GENERIC-ISO ZZ CN 163 125 6463
N416 Cylindrical Roller NTN open CN 330 315 7140
NF416 Cylindrical Roller NTN open CN 330 315 7140
NJ416 Cylindrical Roller SKF open CN 303 320 7550
NJ416-NTN Cylindrical Roller NTN open CN 330 315 7140
NU416 Cylindrical Roller SKF open CN 303 320 7250
NU416-NTN Cylindrical Roller NTN open CN 330 315 7140
NUP416 Cylindrical Roller NTN open CN 330 315 7140

Note: catalogue dynamic load ratings for this envelope span 163.0– 330.0 kN — a 102% spread between designs in the very same 80×200×48 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 80 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6416, 6416-2RS, 6416-NTN, 6416-ZZ, N416, NF416, NJ416, NJ416-NTN, NU416, NU416-NTN, NUP416.

Frequently asked questions

Are all 80×200×48 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 80 mm bore, 200 mm OD, 48 mm width (3.150×7.874×1.890 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 11 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 80×200×48?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 80×200×48 mm in inches?

80×200×48 mm converts to 3.150×7.874×1.890 in, with a 60 mm (2.362 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6416, 6416-2RS, 6416-NTN mount in the same space despite different internal designs.