5205SCLLD bearing: complete specifications & equivalents
The 5205SCLLD is a ISO 15 radial bearing sized 25 x 52 x 20.6 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 25 mm |
| Outer diameter D | 52 mm |
| Width B | 20.6 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 16.9 kN |
| Basic static load rating C0 | 12.3 kN |
| Fatigue load limit Pu | 0.74 kN |
| Limiting speed (mechanical) | 7500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 180 g |
| Manufacturer designation | NTN 5205SCLLD |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 5200S-series range
| Bore d | 0.984 in |
|---|---|
| Outer diameter D | 2.047 in |
| Width B | 0.811 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 13.5 mm |
| Smallest bore in 5200S-series | 10 mm |
| Largest outer diameter in 5200S-series | 150 mm |
| Width range across 5200S-series | 14.3–49.2 mm |
| Bore position in 5200S-series (smallest first) | 6 of 18 |
| Bore above smallest 5200S-series size | 15 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 5205SCLLD | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 5205SCLLD model number is decoded
From the medium-duty 5200S double-row family, 5205SCLLD measures 25 mm across the bore, 52 mm over the outer ring and 20.6 mm across the faces. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 05 encodes the 25 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. At roughly 13.5 mm of radial section, the catalogue still quotes 16.9 kN dynamic capacity for the 25 mm bore. For a 25 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 25 mm bore give the working limits.
Typical equipment & failure modes
Common applications
- small pump and compressor shafts with combined load
- servo and stepper motor shafts with axial preload
- bicycle and motorcycle wheel and steering positions
- small gearbox pinion shafts with helical gears
Known failure patterns
- impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle
- thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear
- pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed
- lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated
- contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue
Selection pitfalls — read before you substitute
- At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.
- Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.
- The C0 of 12.3 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.
- Never use a four-point or double-row bearing as a like-for-like swap for a single 5205SCLLD without re-checking axial float, heat and housing width — the kinematics differ.
- Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.
- The 16.9/12.3 kN ratings and 0.74 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5205SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 5205SCLLD?
5205SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 25 mm bore, 52 mm outside diameter, 20.6 mm width (0.984 x 2.047 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 16.9 kN, C0 12.3 kN and a 0.74 kN fatigue load limit Pu; the grease limiting speed is 7,500 r/min and no oil rating is printed for this execution; mass about 180 g.
How is the 5205SCLLD designation structured?
52 is the double-row dimension series (medium-duty 5200S double-row family); 05 encodes the 25 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 52 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series.
Which axial direction does 5205SCLLD support?
5205SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating).
What lubrication speeds does NTN print for 5205SCLLD?
Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,500 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit.
What should be checked before substituting another make for 5205SCLLD?
The 25/52/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 16.9 kN / C0 12.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.