7009 bearing: complete specifications & equivalents
The 7009 is a ISO 15 radial bearing sized 45 x 75 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 45 mm |
| Outer diameter D | 75 mm |
| Width B | 16 mm |
| Seal / shield | open |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | brass |
| Operating temperature | -40 to +150 °C |
| Mass (geometry estimate) | 231 g |
| Standard | ISO 15 |
| Catalog version | iso15-ed4-geometry |
| Last verified | 2026-09-24 |
Source: ISO 15 boundary-dimensions standard · extracted 2026-09-24
Standard-interchange bearing: dimensions per ISO 15; CN clearance, P0 tolerance and a stamped-steel cage are catalogue defaults unless the supplier states otherwise, and mass is a geometry-derived estimate. Brand catalogue load ratings and limiting speeds for 7009 are being backfilled — use the inquiry form for certified values.
Dimensions in inches & 7000-series range
| Bore d | 1.772 in |
|---|---|
| Outer diameter D | 2.953 in |
| Width B | 0.63 in |
| ISO bore code | 09 |
| Radial section height (D−d)/2 | 15 mm |
| Smallest bore in 7000-series | 10 mm |
| Largest outer diameter in 7000-series | 170 mm |
| Width range across 7000-series | 8–28 mm |
| Bore position in 7000-series (smallest first) | 10 of 23 |
| Bore above smallest 7000-series size | 35 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 7009 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 7009 model number is decoded
In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7009 carries bore code 09 = 45 mm. Outside diameter 75 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6009 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 45 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.
Typical equipment & failure modes
Common applications
- gear reducers
- electric motor shafts
- conveyor head pulleys
- pump and compressor shafts
Known failure patterns
- preload loss after a paired set runs loose, letting the balls skid and smear the raceway
- raceway smearing under marginal lubrication at start-up before oil climb reaches the contact
- cage fracture from operation beyond the limiting speed with inadequate lubricant
- fretting corrosion on a loose shaft seat that lets the inner ring creep
Selection pitfalls — read before you substitute
- At a 45 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.
- The 70xx extra-light section at 45 mm bore uses a 75 mm OD; axial capacity is lower than a 7209, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.
- The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.
- Angular-contact 7009 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.
Frequently asked questions
What are the dimensions of a 7009 angular-contact bearing?
A 7009 single-row angular-contact ball bearing has a 45 mm bore, 75 mm outer diameter and 16 mm width (1.772 × 2.953 × 0.63 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 231 g for a brass-cage unit; catalogue masses vary with cage and ball complement.
How does the 7009 bore code work?
The last two digits of 7009 are bore code 09, giving 09 × 5 = 45 mm bore. The 75 mm outside diameter and 16 mm width follow the ISO 15 diameter series, shared with the 6009 deep-groove envelope.
What is the contact angle of 7009?
The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue.
Can a single 7009 take axial load in both directions?
No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load.
How does 7009 compare with a deep-groove 6009?
Both share the 45×75×16 mm ISO 15 envelope (15.0 mm radial section), but the angular-contact 7009 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6009.
Reviewed & verified by the MPN Base engineering desk against source catalog iso15-ed4-geometry on 2026-09-24. Read our editorial & correction policy.