MPNbase

45×75×16 mm bearings

21 models from 4 brands across 3 types share this ISO 15 envelope: 45 mm bore, 75 mm outside diameter, 16 mm width (1.772×2.953×0.630 in), 15 mm radial section.

21 models fit this space 4 brands 20 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6009 Deep Groove Ball SKF open CN 22.1 14.6 240
6009-2RS Deep Groove Ball SKF 2RS CN 22.1 14.6 250
6009-2RS-NSK Deep Groove Ball NSK 2RS CN 23 15.2 241
6009-2RS-NTN Deep Groove Ball NTN 2RS CN 23.2 15.1 237
6009-NSK Deep Groove Ball NSK open CN 23 15.2 241
6009-NTN Deep Groove Ball NTN open CN 23.2 15.1 237
6009-RSR Deep Groove Ball NSK RSR CN 23 15.2 241
6009-RSR-NTN Deep Groove Ball NTN RSR CN 23.2 15.1 237
6009-ZZ Deep Groove Ball SKF ZZ CN 22.1 14.6 250
6009-ZZ-NSK Deep Groove Ball NSK ZZ CN 23 15.2 241
6009-ZZ-NTN Deep Groove Ball NTN ZZ CN 23.2 15.1 237
7009 Angular Contact Ball GENERIC-ISO open CN — — 231
7009-NTN Angular Contact Ball NTN open CN 24.7 17.7 282
N1009 Cylindrical Roller NTN open CN 34.5 34 276
NJ1009 Cylindrical Roller NTN open CN 34.5 34 276
NJ1009-ECP Cylindrical Roller SKF open CN 44.6 52 260
NU1009 Cylindrical Roller NTN open CN 34.5 34 276
NU1009-ECP Cylindrical Roller SKF open CN 44.6 52 250
NUP1009 Cylindrical Roller NTN open CN 34.5 34 276
W6009-2RS Deep Groove Ball SKF 2RS CN 18.2 15 236
W6009-ZZ Deep Groove Ball SKF ZZ CN 18.2 15 237

Note: catalogue dynamic load ratings for this envelope span 18.2– 44.6 kN — a 145% spread between designs in the very same 45×75×16 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 45 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6009, 6009-2RS, 6009-2RS-NSK, 6009-2RS-NTN, 6009-NSK, 6009-NTN, 6009-RSR, 6009-RSR-NTN, 6009-ZZ, 6009-ZZ-NSK, 6009-ZZ-NTN, 7009, 7009-NTN, N1009, NJ1009, NJ1009-ECP, NU1009, NU1009-ECP, NUP1009, W6009-2RS, W6009-ZZ.

Frequently asked questions

Are all 45×75×16 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 45 mm bore, 75 mm OD, 16 mm width (1.772×2.953×0.630 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 21 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 45×75×16?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 45×75×16 mm in inches?

45×75×16 mm converts to 1.772×2.953×0.630 in, with a 15 mm (0.591 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6009, 6009-2RS, 6009-2RS-NSK mount in the same space despite different internal designs.