6009-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6009-NSK model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6009 carries bore code 09 = 45 mm. Outside diameter 75 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 45 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 45 mm shaft for 6009 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• Choosing the 60xx extra-light section saves radial space at 45 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6209 before committing to the smaller envelope.
• The open 6009-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 45×75×16 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6000-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6009 units.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 6000-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Do not quieten a noisy bearing by preloading it: the 6000-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• The open 6009 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 45 mm bore puts 6009 in NSK's general-purpose industrial range; the standard pressed-steel cage and CN clearance cover most electric-motor and pump duty. NSK's VV non-contact seal is the high-speed choice here — DDU contact seal costs roughly 30–40% of the open-bearing speed ceiling.
• At 23 kN dynamic load rating (C) and 15.2 kN static (C0), 6009 is a medium-load NSK bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NSK catalogue.
• At 241 g, 6009 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 45×75×16 mm envelope of 6009 gives a D/d ratio of 1.67 and 15.0 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 23/15.2 kN load ratings, mass 241 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6009 on the 45×75×16 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6009 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 6009; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.