6009-RSR bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6009-RSR model number is decoded

6009-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 09 by five gives the 45 mm bore; the 75 mm outside diameter and 16 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 45 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK's non-contact seal suffix is VV (catalogue number 6009VV), mapped here from the industry-neutral -RSR spelling; speed capability is close to the open bearing but VV is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Sizes around 45 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 6009-RSR.
• Choosing the 60xx extra-light section saves radial space at 45 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6209 before committing to the smaller envelope.
• RSR low-friction seals on 6009-RSR run faster than contact-seal 6009-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 6009-2RS instead.
• The non-contact lip of 6009-RSR does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 45 mm bore position before relying on it as sealed-for-life.
• Do not quieten a noisy bearing by preloading it: the 6000-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Measure the shaft, do not trust the drawing: a 45 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6009-RSR.
• NSK catalogues this low-friction non-contact seal as 6009VV (suffix VV), mapped here from the industry-neutral -RSR spelling. NSK rates its speed capability close to the open bearing, but VV is not liquid-tight — for wet or fine-dust duty step up to the DDU contact seal (industry-neutral -2RS).
• The 45 mm bore puts 6009 in NSK's general-purpose industrial range; the standard pressed-steel cage and CN clearance cover most electric-motor and pump duty. NSK's VV non-contact seal is the high-speed choice here — DDU contact seal costs roughly 30–40% of the open-bearing speed ceiling.
• At 23 kN dynamic load rating (C) and 15.2 kN static (C0), 6009 is a medium-load NSK bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NSK catalogue.
• At 241 g, 6009 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 45×75×16 mm envelope of 6009 gives a D/d ratio of 1.67 and 15.0 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 23/15.2 kN load ratings, mass 241 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6009VV on the 45×75×16 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6009 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.