7213-BECBY bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7213-BECBY model number is decoded

7213 BECBY is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 65×120×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 69.5 kN, C0 57 kN, Pu 2.45 kN.reference speed 6,700 r/min (thermal) and limiting speed 6,700 r/min (mechanical), which coincide for this size, catalogue mass 1000 g. Sizing arithmetic on the 65 mm bore: 69.5 kN C divided by the 27.5 mm radial section height gives 2.5 kN per section millimetre; the 1000 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. The 2.45 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 69.5/57 kN ratings and 1000 g mass this execution carries about 1.07 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Assign interference to the rotating ring — roughly k5 on a 65 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.
• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.
• Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.
• The steep 40° angle of 7213-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.