7220-BECBY bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7220-BECBY model number is decoded

7220 BECBY is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 100×180×34 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 100×180×34 mm (3.937×7.087×1.339 in), 40.0 mm radial section height, C 143 kN, C0 134 kN, Pu 4.75 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 3300 g. Mass and section check: 3300 g inside the 100×180×34 mm outline leaves a 40.0 mm radial section, and the 134 kN static rating is 0.94× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 4,500 r/min the mean pitch diameter dm ≈ 140.0 mm implies a dn value around 630k mm·r/min; the 4,300 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 4,300 r/min against a 4,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.96. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.
• Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.
• The steep 40° angle of 7220-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.