7236B bearing: complete specifications & equivalents
The 7236B is a ISO 15 radial bearing sized 180 x 320 x 52 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 180 mm |
| Outer diameter D | 320 mm |
| Width B | 52 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 305 kN |
| Basic static load rating C0 | 350 kN |
| Fatigue load limit Pu | 16.1 kN |
| Limiting speed (mechanical) | 1800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 17700 g |
| Manufacturer designation | NTN 7236B |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 7200-series range
| Bore d | 7.087 in |
|---|---|
| Outer diameter D | 12.598 in |
| Width B | 2.047 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 70 mm |
| Smallest bore in 7200-series | 10 mm |
| Largest outer diameter in 7200-series | 540 mm |
| Width range across 7200-series | 9–85 mm |
| Bore position in 7200-series (smallest first) | 30 of 36 |
| Bore above smallest 7200-series size | 170 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 7236B model number is decoded
From the medium-duty 7200 single-row family, 7236B measures 180 mm across the bore, 320 mm over the outer ring and 52 mm across the faces. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 36 encodes the 180 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). With C 305 kN and C0 350 kN, each mm of bore carries about 1.69 kN of dynamic rating. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated.
Typical equipment & failure modes
Common applications
- large pump and turbine auxiliary shafts
- steel-plant conveyor and table roll drives
- wind-turbine and heavy-machinery auxiliaries
- heavy industrial gearbox main shafts
Known failure patterns
- impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle
- loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow
- resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer
- edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face
- lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated
Selection pitfalls — read before you substitute
- At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 180 mm bore bearing forgives nothing in a poorly machined housing.
- The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.
- A 7236B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.
- If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.
- On a 180 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.
- The 305/350 kN ratings and 16.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7236B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 7236B?
7236B is a single-row angular contact ball bearing to ISO 15: 180 mm bore, 320 mm outside diameter, 52 mm width (7.087 x 12.598 x 2.047 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 305 kN, C0 350 kN and a 16.1 kN fatigue load limit Pu; the grease limiting speed is 1,800 r/min and the oil rating 2,400 r/min; mass about 17700 g.
How is the 7236B designation structured?
72 is the single-row dimension series (medium-duty 7200 single-row family); 36 encodes the 180 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 320 mm OD and 52 mm width follow the ISO 15 boundary-dimension plan for that series.
Which axial direction does 7236B support?
One 7236B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact.
What lubrication speeds does NTN print for 7236B?
Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,800 r/min and the oil rating 2,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit.
What should be checked before substituting another make for 7236B?
The 180/320/52 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 305 kN / C0 350 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.