7305-BECBP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7305-BECBP model number is decoded

7305 BECBP is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 25×62×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 26.5 kN, C0 15.3 kN, Pu 0.655 kN.reference speed 14,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 230 g. Mass and section check: 230 g inside the 25×62×17 mm outline leaves a 18.5 mm radial section, and the 15.3 kN static rating is 0.58× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 0.655 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 26.5/15.3 kN ratings and 230 g mass this execution carries about 1.06 kN of C per millimetre of bore. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.
• Fillet radii must clear the chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
• Assign interference to the rotating ring — roughly k5 on a 25 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.
• Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.
• The steep 40° angle of 7305-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.