7306-BECBP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7306-BECBP model number is decoded

7306 BECBP is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 30×72×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 35.5 kN, C0 21.2 kN, Pu 0.9 kN.reference speed 12,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 340 g. Envelope economics: the 19 mm width over a 21.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 340 g for 35.5 kN of dynamic capacity — about 10 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 13,000 r/min while thermal balance under catalogue load sets the 12,000 r/min reference; at dm ≈ 51.0 mm the corresponding dn is approximately 663k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 12,000 r/min against a 13,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.92. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.
• Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.
• Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.
• At 30 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.
• The steep 40° angle of 7306-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.