7309-BE-2RZP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7309-BE-2RZP model number is decoded

7309 BE-2RZP is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 45×100×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 55.9 kN, C0 37.5 kN, Pu 1.6 kN.reference speed 8,500 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 850 g. Sizing arithmetic on the 45 mm bore: 55.9 kN C divided by the 27.5 mm radial section height gives 2.0 kN per section millimetre; the 850 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 1.6 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 55.9/37.5 kN ratings and 850 g mass this execution carries about 1.24 kN of C per millimetre of bore. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.
• Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.
• Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.
• The steep 40° angle of 7309-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• The non-contact -2RZ seals of 7309-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing.