7318-BECBY bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7318-BECBY model number is decoded

7318 BECBY is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 90×190×43 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 166 kN, C0 146 kN, Pu 5.3 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 5200 g. Load balance: C0 146 kN against C 166 kN gives a 0.88 ratio, typical of a steep-angle axial-oriented design; Pu 5.3 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 5200 g inside the 90×190×43 mm outline leaves a 50.0 mm radial section, and the 146 kN static rating is 0.88× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 43 mm width gives a bore/width ratio of 2.09; use these ratios when housing space around the 90 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• One 7318-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.
• At 90 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.
• Fillet radii must clear the chamfer so the 43 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
• Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.
• The steep 40° angle of 7318-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.