7319-BEP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7319-BEP model number is decoded

7319 BEP is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 95×200×45 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 95×200×45 mm (3.74×7.874×1.772 in), 52.5 mm radial section height, C 168 kN, C0 150 kN, Pu 5.2 kN.reference speed 4,000 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 6050 g. Envelope economics: the 45 mm width over a 52.5 mm section yields 0.86 mm of ring width per section millimetre, and the bearing weighs 6050 g for 168 kN of dynamic capacity — about 36 g per rated kN. Mass and section check: 6050 g inside the 95×200×45 mm outline leaves a 52.5 mm radial section, and the 150 kN static rating is 0.89× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 200 over bore 95 is a 2.11× step for this size, and the 45 mm width gives a bore/width ratio of 2.11; use these ratios when housing space around the 95 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Greased positions should fill roughly 25–35 % of the free volume on a 7319-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.
• Assign interference to the rotating ring — roughly k5 on a 95 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.
• Fillet radii must clear the chamfer so the 45 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
• One 7319-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.
• The steep 40° angle of 7319-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Catalogue ratings are SKF PUB BU/P1 17000 figures for 7319 BEP as the single basic pa66 execution; the other order numbers of the 7319 size are different products and may carry different ratings — always quote the full designation when purchasing.