16064-MA bearing: complete specifications & equivalents

The 16064-MA is a ISO 15 radial bearing sized 320 x 480 x 50 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 480 mm d = 320 B = 50 mm side section front view
Principal dimensions: bore d 320 mm, outer diameter D 480 mm, width B 50 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 320 mm
Outer diameter D 480 mm
Width B 50 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 281 kN
Basic static load rating C0 405 kN
Fatigue load limit Pu 8.65 kN
Reference speed (thermal) 2600 rpm
Limiting speed (mechanical) 2200 rpm
Operating temperature -40 to +120 °C
Mass 34000 g
Manufacturer designation 16064 MA
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 16000-series range

Bore d12.598 in
Outer diameter D18.898 in
Width B1.969 in
ISO bore code64
Radial section height (D−d)/280 mm
Smallest bore in 16000-series12 mm
Largest outer diameter in 16000-series560 mm
Width range across 16000-series7–57 mm
Bore position in 16000-series (smallest first)37 of 40
Bore above smallest 16000-series size308 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
16064 NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
NTN bearing 16064 on the same 320×480×50 mm envelope, but catalogue C/C0 differ (281/405 kN vs 335/440 kN) — envelope interchange only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 16064-MA model number is decoded

In the 16000-series, the last two digits encode the bore: 16064 carries code 64 = 320 mm (code × 5). The envelope is 320×480×50 mm (12.598×18.898×1.969 in) with a 80.0 mm radial section height, C 281 kN, C0 405 kN and Pu 8.65 kN. The open 16064 MA carries no shields or seals and relies on application lubrication and external sealing. The MA suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 2200 r/min, catalogue mass 34000 g. A thin section saves space but leaves little margin for misalignment or shaft deflection.

Typical equipment & failure modes

Common applications

  • textile and packaging machinery
  • slew and indexing drives
  • large industrial gearboxes
  • heavy conveyor drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • edge loading from shaft deflection or housing misalignment
  • rolling-contact fatigue spalling once the catalogue L10 life is exceeded

Selection pitfalls — read before you substitute

  • Clearance suffixes follow the seal code in the designation stack (e.g. 16064-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Deep-groove geometry tolerates only minutes of misalignment; if the 480 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 16064-MA.
  • The MA suffix on 16064-MA denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 34000 g quoted mass includes the heavier cage.
  • Open 16064-MA needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 16064-MA; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 16064-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • A replacement 16064 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.
  • Where two 16064 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.

Frequently asked questions

What are the dimensions of 16064-MA?

The SKF 16064 MA measures 320 mm bore × 480 mm OD × 50 mm width (12.598 × 18.898 × 1.969 in), mass about 34000 g. It is open, with no shields or seals.

How does the bore code in 16064 work?

The final two digits of 16064 are bore code 64, multiplied by 5 to give 320 mm.

What is the speed rating of 16064-MA?

SKF lists a 2600 r/min thermal reference speed and a 2200 r/min mechanical limiting speed for 16064 MA; real limits also depend on lubrication and fits.

What is the difference between 16064-MA and a same-bore 62-series bearing?

Section height differs: 16064-MA has a 80 mm radial section and C 281 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.

Which fits should I use for 16064-MA?

With a rotating inner ring use roughly m6 on the shaft and H7 in the 480 mm housing; reverse the interference if the outer ring rotates.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.