213 bearing: complete specifications & equivalents
The 213 is a ISO 15 radial bearing sized 65 x 120 x 23 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 65 mm |
| Outer diameter D | 120 mm |
| Width B | 23 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 60.5 kN |
| Basic static load rating C0 | 58.5 kN |
| Fatigue load limit Pu | 2.5 kN |
| Reference speed (thermal) | 10000 rpm |
| Limiting speed (mechanical) | 6000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1050 g |
| Manufacturer designation | 213 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 200-series range
| Bore d | 2.559 in |
|---|---|
| Outer diameter D | 4.724 in |
| Width B | 0.906 in |
| ISO bore code | 13 |
| Radial section height (D−d)/2 | 27.5 mm |
| Smallest bore in 200-series | 30 mm |
| Largest outer diameter in 200-series | 180 mm |
| Width range across 200-series | 16–34 mm |
| Bore position in 200-series (smallest first) | 8 of 15 |
| Bore above smallest 200-series size | 35 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6213-2RS | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | NSK bearing NSK 6213DDU on the same 65×120×23 mm envelope, but catalogue C/C0 differ (60.5/58.5 kN vs 63/40 kN) — envelope interchange only after a load check. |
| 6213-RSR | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | NSK bearing NSK 6213VV on the same 65×120×23 mm envelope, but catalogue C/C0 differ (60.5/58.5 kN vs 63/40 kN) — envelope interchange only after a load check. |
| 6213-M | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 65×120×23 mm envelope as SKF 6213 M, but catalogue C/C0 differ (60.5/58.5 kN vs 58.5/40.5 kN) — envelope match only after a load check. |
| 213-ZZ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 65×120×23 mm envelope and equivalent catalogue ratings; 213-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 6213 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6213 shares the 65×120×23 mm envelope but catalogue C/C0 differ (60.5/58.5 kN vs 58.5/40.5 kN) — envelope match, not a load-rating equivalent. |
| 6213-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6213-2Z shares the 65×120×23 mm envelope but catalogue C/C0 differ (60.5/58.5 kN vs 58.5/40.5 kN) — envelope match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 213 model number is decoded
213 is a filling-slot (notched-ring) deep-groove bearing in the legacy 200-series: the last two digits encode the bore: 213 carries code 13 = 65 mm (code × 5). The rings carry loading slots that allow extra balls during assembly, which is what gives the 65×120×23 mm envelope its C 60.5 kN and C0 58.5 kN ratings (Pu 2.5 kN). The open 213 carries no shields or seals and relies on application lubrication and external sealing. Limiting speed 6000 r/min, mass 1050 g. These bearings are built for high purely-radial loads at moderate speeds.
Typical equipment & failure modes
Common applications
- eccentric and vibratory conveyors
- legacy machinery repairs
- slew drives
- material-handling winches
Known failure patterns
- spalling of the filling-slot edge when balls are hammered through the slot under heavy thrust loading
- dirt entering through the open slot area when external sealing is neglected
- fretting corrosion on a creeping shaft or housing seat
- cage damage from running beyond the limiting speed
Selection pitfalls — read before you substitute
- Filling-slot bearings take heavy purely-radial load at moderate speed but little thrust; the 60.5/58.5 kN ratings assume radial loading — use deep-groove 6xxx where axial load matters.
- Shields on 213 retain grease but do not seal against water; for wet farm duty add external lip seals rather than trusting the shield.
- Limiting speed is just 6000 r/min: filling-slot cages and the slot geometry run cooler below that — overspeed drives cage wear and smearing.
- Filling slots let more balls be packed into the 65×120 mm envelope, which is why 213 reaches C 60.5 kN — but the slots also mean the two rings separate when the balls align with them, so handle it as a loose-clearance design.
- Limiting speed is just 6000 r/min: filling-slot cages and the slot geometry run cooler below that — overspeed drives cage wear and smearing.
- Catalogue ratings for 213 (C 60.5 kN, C0 58.5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
Frequently asked questions
What are the dimensions of 213?
Filling-slot bearing 213 measures 65×120×23 mm (2.559×4.724×0.906 in), about 1050 g.
What does the designation 213 mean?
It is the legacy 200/300 filling-slot numbering: series 200 and bore code 13 = 65 mm. Filling-slot bearings predate the 6xxx deep-groove spelling.
Is 213 available sealed?
Shielded executions (-2Z, listed here as 213-ZZ) exist; contact-sealed versions are generally not produced for the filling-slot family.
What is a filling-slot bearing?
The inner and outer rings each have a loading slot; when aligned, extra balls can be inserted, raising radial rating (C 60.5 kN for 213). The slots also make the rings separable.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.