6014-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6014-NSK model number is decoded

6014 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 14 by five gives the 70 mm bore; the 110 mm outside diameter and 20 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 70 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 70 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 6014 with C3 for those conditions.
• Choosing the 60xx extra-light section saves radial space at 70 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6214 before committing to the smaller envelope.
• Storage matters for open bearings: 6014-NSK leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 6000-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6014 units.
• Measure the shaft, do not trust the drawing: a 70 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6014-NSK.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6014-NSK-C3. No clearance suffix means normal CN clearance.
• The open 6014 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• At 70 mm bore 6014 is in NSK's upper general-purpose range; the pressed-steel cage is standard, but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• NSK rates 6014 at 42 kN dynamic (C) and 31 kN static (C0); this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 608 g, 6014 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 70×110×20 mm envelope of 6014 gives a D/d ratio of 1.57 and 20.0 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 42/31 kN load ratings, mass 608 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6014 on the 70×110×20 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6014 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.
• NSK's VV non-contact seal keeps frictional torque close to the open 6014; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.