6032-ZZ-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6032-ZZ-NSK model number is decoded

In the 6000-series (diameter series 0 of ISO 15) the last two digits encode the bore: 6032 carries bore code 32 = 160 mm. Outside diameter 240 mm and width 38 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 160 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NSK catalogue order number: 6032ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 160 mm bore the ring mass is significant: heat 6032 on an induction heater (max 120 °C), never over an open flame, and plan puller access or a withdrawal sleeve now for the day it has to come off again.
• The 60xx extra-light section at 160 mm bore uses a smaller 240 mm OD than a 6232; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
• ZZ shields are non-contact: 6032-ZZ-NSK blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6032-2RS for that.
• Do not wash 6032-ZZ-NSK in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6032-ZZ-NSK-C3. No clearance suffix means normal CN clearance.
• Never mix components between two 6032-ZZ-NSK units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• NSK catalogues the shielded version as 6032ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NSK order number when buying through an NSK channel.
• The 160 mm bore places 6032 at the lower end of NSK's large-size range; at these diameters the pressed-steel cage is speed-limited and NSK commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NSK distributor, and do not extrapolate small-bore speed ratings to this size.
• NSK rates 6032 at 150 kN dynamic (C) and 135 kN static (C0); this heavy-load rating is at the upper end of the E1103 Part C single-row deep-groove extract — NSK supplies a machined brass cage (suffix M) and expects an application review, because catalogue L10 life alone does not capture shock and misalignment loads at this rating.
• At 5150 g (5.2 kg), 6032 is a heavy NSK bearing that requires a crane or hoist for handling; induction-heat the inner ring (max 120 °C) and use a mechanical puller for removal — never apply heat directly to the balls or cage.
• The 160×240×38 mm envelope of 6032 gives a D/d ratio of 1.50 and 40.0 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 150/135 kN load ratings, mass 5150 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6032ZZ on the 160×240×38 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6032 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 6032; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.