6032-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6032-NTN model number is decoded

6032 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 32 by five gives the 160 mm bore; the 240 mm outside diameter and 38 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 160 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 160 mm of 6032-NTN demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• Choosing the 60xx extra-light section saves radial space at 160 mm bore, but the trade-off is rating: if the drive sees shock or frequent start-stop cycles, re-check the L10 life against a 6232 before committing to the smaller envelope.
• The open 6032-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 160×240×38 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6000-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6032 units.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Measure the shaft, do not trust the drawing: a 160 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6032-NTN.
• The open 6032 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 160 mm bore places 6032 at the lower end of NTN's large-size range; at these diameters the pressed-steel cage is speed-limited and NTN commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NTN distributor, and do not extrapolate small-bore speed ratings to this size.
• NTN lists the grease limiting speed at 2600 r/min for 6032; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 158 kN dynamic load rating (C) and 144 kN static (C0), 7.3 kN fatigue load limit Cu, 6032 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 5050 g (5.0 kg), 6032 is a heavy bearing that requires a crane or hoist for handling; induction-heat the inner ring (max 120 °C) and use a mechanical puller for removal — never apply heat directly to the balls or cage.
• The 160×240×38 mm envelope of 6032 gives a D/d ratio of 1.50 and 40.0 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 158/144 kN load ratings, 7.3 kN fatigue load limit Cu NTN lists the grease limiting speed at 2600 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 5050 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6032 on the 160×240×38 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6032 in a rated drive.
• Standard catalogue stock of 6032 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.