607-RSR bearing: complete specifications & equivalents
The 607-RSR is a ISO 15 radial bearing sized 7 x 19 x 6 mm (bore x OD x width) with RSR sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 7 mm |
| Outer diameter D | 19 mm |
| Width B | 6 mm |
| Material | GCr15 |
| Seal / shield | RSR |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 2.34 kN |
| Basic static load rating C0 | 0.95 kN |
| Fatigue load limit Pu | 0.04 kN |
| Reference speed (thermal) | 85000 rpm |
| Limiting speed (mechanical) | 43000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 7.8 g |
| Manufacturer designation | 607-2RSL |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6000-series range
| Bore d | 0.276 in |
|---|---|
| Outer diameter D | 0.748 in |
| Width B | 0.236 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 6 mm |
| Smallest bore in 6000-series | 4 mm |
| Largest outer diameter in 6000-series | 1150 mm |
| Width range across 6000-series | 4–155 mm |
| Bore position in 6000-series (smallest first) | 4 of 61 |
| Bore above smallest 6000-series size | 3 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 607 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 7×19×6 mm envelope and equivalent catalogue ratings; 607 is the open arrangement execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 607-2RS | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 7×19×6 mm envelope and equivalent catalogue ratings; 607-2RSH is the two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 607-ZZ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 7×19×6 mm envelope and equivalent catalogue ratings; 607-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| W607-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 7×19×6 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (2.34/0.95 kN vs 1.53/0.585 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| W607-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 7×19×6 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (2.34/0.95 kN vs 1.53/0.585 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| W607 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 7×19×6 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (2.34/0.95 kN vs 1.53/0.585 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 607-RSR model number is decoded
In the 6000-series, the final digit is the bore in millimetres: 607 fits a 7 mm shaft (direct-number miniature spelling). The envelope is 7×19×6 mm (0.276×0.748×0.236 in) with a 6.0 mm radial section height, C 2.34 kN, C0 0.95 kN and Pu 0.04 kN. SKF lists this as 607-2RSL with a low-friction non-contact seal (2RSL/2RZ spelling): it runs near open-bearing speed with less drag than a contact seal but is not liquid-tight. Limiting speed 43000 r/min, catalogue mass 7.8 g.
Typical equipment & failure modes
Common applications
- office equipment
- fractional-horsepower motors
- small fans and blowers
- hand-held power tools
Known failure patterns
- fine dust or moisture passing the low-friction non-contact lip in dirty or wet duty
- grease loss past the low-drag seal when no regreasing schedule is kept
- fretting corrosion on a creeping shaft or housing seat
- cage damage from running beyond the limiting speed
Selection pitfalls — read before you substitute
- Assign interference to the rotating ring: on a conventional shaft-mounted 7 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
- Clearance suffixes follow the seal code in the designation stack (e.g. 607-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
- The low-friction seal on 607-RSR saves drag versus a contact lip but is not liquid-tight; wet or chemically aggressive positions need the 2RS version.
- Do not pry the caps off 607-RSR to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
- Assign interference to the rotating ring: on a conventional shaft-mounted 7 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
- Deep-groove geometry tolerates only minutes of misalignment; if the 19 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 607-RSR.
Frequently asked questions
What are the dimensions of 607-RSR?
The SKF 607-2RSL measures 7 mm bore × 19 mm OD × 6 mm width (0.276 × 0.748 × 0.236 in), mass about 7.8 g. It has two low-friction non-contact rubber seals.
How do I read the 607 designation?
Small miniature bearings print the bore as the final digit, so 607 is a 7 mm bearing; the series digits in front give the section (OD/width family).
What load can 607-RSR take?
Catalogue values for 607-2RSL: dynamic C 2.34 kN, static C0 0.95 kN, fatigue limit Pu 0.04 kN. Use C in life calculation and C0 for static checks at 7 mm bore.
What is the speed rating of 607-RSR?
SKF lists a 85000 r/min thermal reference speed and a 43000 r/min mechanical limiting speed for 607-2RSL; real limits also depend on lubrication and fits.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.