6072-M bearing: complete specifications & equivalents

The 6072-M is a ISO 15 radial bearing sized 360 x 540 x 82 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 540 mm d = 360 B = 82 mm side section front view
Principal dimensions: bore d 360 mm, outer diameter D 540 mm, width B 82 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 360 mm
Outer diameter D 540 mm
Width B 82 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 442 kN
Basic static load rating C0 695 kN
Fatigue load limit Pu 14 kN
Reference speed (thermal) 2400 rpm
Limiting speed (mechanical) 1900 rpm
Operating temperature -40 to +120 °C
Mass 64500 g
Manufacturer designation 6072 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6000-series range

Bore d14.173 in
Outer diameter D21.26 in
Width B3.228 in
ISO bore code72
Radial section height (D−d)/290 mm
Smallest bore in 6000-series4 mm
Largest outer diameter in 6000-series1150 mm
Width range across 6000-series4–155 mm
Bore position in 6000-series (smallest first)46 of 61
Bore above smallest 6000-series size356 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6072 NTN full
Dimensions and internal design equivalent — standard interchange.
NTN counterpart 6072 on the same 360×540×82 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6072-M model number is decoded

In the 6000-series, the last two digits encode the bore: 6072 carries code 72 = 360 mm (code × 5). The envelope is 360×540×82 mm (14.173×21.26×3.228 in) with a 90.0 mm radial section height, C 442 kN, C0 695 kN and Pu 14 kN. The open 6072 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 1900 r/min, catalogue mass 64500 g.

Typical equipment & failure modes

Common applications

  • industrial fans and blowers
  • mill and kiln auxiliaries
  • pulp and paper machinery
  • marine deck machinery

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • electrical pitting in VFD-driven motors without shaft grounding
  • edge loading from shaft deflection or housing misalignment

Selection pitfalls — read before you substitute

  • The fatigue load limit is 14 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
  • Mount by heating the inner ring (max 120 °C) — driving 6072-M home through the outer ring or balls brinells the raceways.
  • The M suffix on 6072-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 64500 g quoted mass includes the heavier cage.
  • Open 6072-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6072-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Fillet radii must clear the 6072-M chamfer so the 82 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • For positions that need relubrication, choose the open execution of 6072 and design the housing with a grease path; shielded and sealed versions are intended as fit-and-forget units.
  • Where two 6072 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.

Frequently asked questions

What are the dimensions of 6072-M?

The SKF 6072 M measures 360 mm bore × 540 mm OD × 82 mm width (14.173 × 21.26 × 3.228 in), mass about 64500 g. It is open, with no shields or seals.

How does the bore code in 6072 work?

The final two digits of 6072 are bore code 72, multiplied by 5 to give 360 mm.

What internal clearance does 6072-M have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 6072-M be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 6072-M take?

Catalogue values for 6072 M: dynamic C 442 kN, static C0 695 kN, fatigue limit Pu 14 kN. Use C in life calculation and C0 for static checks at 360 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.