618-1180-MB bearing: complete specifications & equivalents

The 618-1180-MB is a ISO 15 radial bearing sized 1180 x 1420 x 106 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 1420 mm d = 1180 B = 106 mm side section front view
Principal dimensions: bore d 1180 mm, outer diameter D 1420 mm, width B 106 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 1180 mm
Outer diameter D 1420 mm
Width B 106 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 761 kN
Basic static load rating C0 2360 kN
Fatigue load limit Pu 27.5 kN
Reference speed (thermal) 560 rpm
Limiting speed (mechanical) 480 rpm
Operating temperature -40 to +120 °C
Mass 337000 g
Manufacturer designation 618/1180 MB
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 61800-series range

Bore d46.457 in
Outer diameter D55.906 in
Width B4.173 in
ISO bore code—
Radial section height (D−d)/2120 mm
Smallest bore in 61800-series1 mm
Largest outer diameter in 61800-series1820 mm
Width range across 61800-series1–140 mm
Bore position in 61800-series (smallest first)72 of 74
Bore above smallest 61800-series size1179 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 618-1180-MB model number is decoded

In the large-bore 61800-series, the bore is written directly after the slash as 1180 mm (large thin-section bores use the slash spelling instead of the two-digit code). The envelope is 1180×1420×106 mm (46.457×55.906×4.173 in) with a 120.0 mm radial section height, C 761 kN, C0 2360 kN and Pu 27.5 kN. The open 618/1180 MB carries no shields or seals and relies on application lubrication and external sealing. The MB suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 480 r/min, catalogue mass 337000 g. A thin section saves space but leaves little margin for misalignment or shaft deflection.

Typical equipment & failure modes

Common applications

  • robotics and automation joints
  • lay shafts and idler shafts
  • textile and packaging machinery
  • slew and indexing drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • brinelling from static overload or hammer blows during mounting
  • false brinelling from vibration while the shaft stands idle

Selection pitfalls — read before you substitute

  • Mount by heating the inner ring (max 120 °C) — driving 618-1180-MB home through the outer ring or balls brinells the raceways.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 618/1180-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • The MB suffix on 618-1180-MB denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 337000 g quoted mass includes the heavier cage.
  • Open 618-1180-MB needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 618-1180-MB; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Catalogue ratings for 618-1180-MB (C 761 kN, C0 2360 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • A replacement 618/1180 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.

Frequently asked questions

What are the dimensions of 618-1180-MB?

The SKF 618/1180 MB measures 1180 mm bore × 1420 mm OD × 106 mm width (46.457 × 55.906 × 4.173 in), mass about 337000 g. It is open, with no shields or seals.

Why is there a slash in the designation 618/1180 MB?

The slash writes a bore that falls outside the two-digit code table: 618/1180 means 1180 mm bore. The site slug 618-1180-MB replaces the slash with a hyphen.

How long can a greased 618-1180-MB be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 618-1180-MB take?

Catalogue values for 618/1180 MB: dynamic C 761 kN, static C0 2360 kN, fatigue limit Pu 27.5 kN. Use C in life calculation and C0 for static checks at 1180 mm bore.

What is the speed rating of 618-1180-MB?

SKF lists a 560 r/min thermal reference speed and a 480 r/min mechanical limiting speed for 618/1180 MB; real limits also depend on lubrication and fits.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.