61803-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61803-NTN model number is decoded

61803 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 17 by five gives the 17 mm bore; the 26 mm outside diameter and 5 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 17 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 17 mm bore the ring mass is significant: heat 61803 on an induction heater (max 120 °C), never over an open flame, and plan puller access or a withdrawal sleeve now for the day it has to come off again.
• Only 4.5 mm of radial section separates bore and OD on the 618xx series at 17 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6217.
• The open 61803-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 17×26×5 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61803 units.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61800-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• The housing bore for the 26 mm OD should be round within IT7; an oval bore pinches the outer ring of 61803-NTN and shows up later as two-point loaded raceway wear.
• The open 61803 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• At 17 mm bore the 61803 sits in NTN's small-bore range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• NTN rates 61803 at 24000 r/min grease limiting speed — this is a high-speed electric-motor range; keep the grease fill at 20–30% of the free bearing volume and avoid mixing grease thickener types if regreasing through the housing.
• At 2.47 kN dynamic load rating (C) and 1.46 kN static (C0), 0.1 kN fatigue load limit Cu, 61803 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 8 g, 61803 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 17×26×5 mm envelope of 61803 gives a D/d ratio of 1.53 and 4.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 2.47/1.46 kN load ratings, 0.1 kN fatigue load limit Cu NTN lists the grease limiting speed at 24000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 8 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6803 on the 17×26×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61803 in a rated drive.
• Order the C3 internal-clearance version (61803 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61803 is listed.