61803-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61803-RSR-NTN model number is decoded

61803-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 17 by five gives the 17 mm bore; the 26 mm outside diameter and 5 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 17 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6803LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 17 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 618xx thin section at 17 mm bore has only a 4.5 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6217.
• The low-drag lip of 61803-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• The non-contact lip of 61803-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 17 mm bore position before relying on it as sealed-for-life.
• Never mix components between two 61803-RSR-NTN units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• Vibration during standstill brinells the raceways of a 17 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• NTN catalogues this low-friction non-contact seal as 6803LLB (suffix LB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 17 mm bore the 61803 sits in NTN's small-bore range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• NTN rates 61803 at 24000 r/min grease limiting speed — this is a high-speed electric-motor range; keep the grease fill at 20–30% of the free bearing volume and avoid mixing grease thickener types if regreasing through the seal lip.
• At 2.47 kN dynamic load rating (C) and 1.46 kN static (C0), 0.1 kN fatigue load limit Cu, 61803 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 8 g, 61803 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 17×26×5 mm envelope of 61803 gives a D/d ratio of 1.53 and 4.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 2.47/1.46 kN load ratings, 0.1 kN fatigue load limit Cu NTN lists the grease limiting speed at 24000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 8 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6803LLB on the 17×26×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61803 in a rated drive.
• Order the C3 internal-clearance version (61803 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.