61804-RSR-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61804-RSR-NSK model number is decoded

61804-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 04 by five gives the 20 mm bore; the 32 mm outside diameter and 7 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 20 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK's non-contact seal suffix is VV (catalogue number 6804VV), mapped here from the industry-neutral -RSR spelling; speed capability is close to the open bearing but VV is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Sizes around 20 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 61804-RSR-NSK.
• Only 6.0 mm of radial section separates bore and OD on the 618xx series at 20 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6204.
• RSR low-friction seals on 61804-RSR-NSK run faster than contact-seal 61804-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61804-2RS instead.
• The low-drag lip of 61804-RSR-NSK barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61800-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• The housing bore for the 32 mm OD should be round within IT7; an oval bore pinches the outer ring of 61804-RSR-NSK and shows up later as two-point loaded raceway wear.
• NSK catalogues this low-friction non-contact seal as 6804VV (suffix VV), mapped here from the industry-neutral -RSR spelling. NSK rates its speed capability close to the open bearing, but VV is not liquid-tight — for wet or fine-dust duty step up to the DDU contact seal (industry-neutral -2RS).
• The 20 mm bore puts 61804 in NSK's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty. NSK's VV non-contact seal is the high-speed choice here — DDU contact seal costs roughly 30–40% of the open-bearing speed ceiling.
• At 4.4 kN dynamic load rating (C) and 2.47 kN static (C0), 61804 is a light-load NSK bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 17 g, 61804 is a lightweight NSK bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 20×32×7 mm envelope of 61804 gives a D/d ratio of 1.60 and 6.0 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 4.4/2.47 kN load ratings, mass 17 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6804VV on the 20×32×7 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61804 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.
• Keep NSK bearings in the original packaging until fitting: the wrapper carries the production lot, and the unopened shelf life of greased sealed units is typically quoted at three to five years in dry, vibration-free storage.