61804-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61804-RSR-NTN model number is decoded

61804-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 04 by five gives the 20 mm bore; the 32 mm outside diameter and 7 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 20 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6804JRLLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 20 mm shaft for 61804 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• The 618xx thin section at 20 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6204.
• RSR low-friction seals on 61804-RSR-NTN run faster than contact-seal 61804-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61804-2RS instead.
• The non-contact lip of 61804-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 20 mm bore position before relying on it as sealed-for-life.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 7 mm-wide ring of 61804-RSR-NTN drags the lip and overheats it.
• Vibration during standstill brinells the raceways of a 20 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• NTN catalogues this low-friction non-contact seal as 6804JRLLB (suffix RLLB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• The 20 mm bore puts 61804 in NTN's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• NTN rates 61804 at 21000 r/min grease limiting speed — this is a high-speed electric-motor range; keep the grease fill at 20–30% of the free bearing volume and avoid mixing grease thickener types if regreasing through the seal lip.
• At 4.45 kN dynamic load rating (C) and 2.47 kN static (C0), 0.18 kN fatigue load limit Cu, 61804 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 19 g, 61804 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 20×32×7 mm envelope of 61804 gives a D/d ratio of 1.60 and 6.0 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 4.45/2.47 kN load ratings, 0.18 kN fatigue load limit Cu NTN lists the grease limiting speed at 21000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 19 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6804JRLLB on the 20×32×7 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61804 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• Standard catalogue stock of 61804 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.